Fogarty's Home Services Before & After Photos

These homeowners called because they were looking to have a full energy evaluation done to see where they can save money and improve energy efficiency.

Our Building Science Specialist arrived at the home and sat with the homeowners to get a good idea of their main concerns and come up with a general plan. Upon evaluation, we discovered that the attic area was filled with old, dirty, inefficient and moldy batt insulation which would need to be removed, the area thoroughly cleaned and treated with MoldX and add enough new, TruSoft blown cellulose insulation to bring the home to meet today's energy efficiency standards. We used 4" SilverGlo along the attic deck and vertical walls. Our specialist also discovered we would need to extend the existing bathroom vent fan out through the roof to further prevent moisture and mold into the attic. We also installed a David Lewis Attic Pull-Down Stair Hatch Cover to properly insulate and air seal the entrance to the attic.

Dr. Energy Saver by Eco Energy Solutions was able to completely remedy the problem and create a satisfactory, energy efficient solution to give the homeowners piece of mind and reach their ultimate goal of saving money on energy usage! 

This homeowner called because they were experiencing "suspicious noises" in their attic and suspected they had a rodent problem.

Our Building Science Specialist went to the home and inspected the attic area. We were able to confirm that there were, in fact, several rodents living in the insulation in the kneewall areas or the unfinished area, outside of the conditioned space, separated by a "kneewall", necessary to support the roof rafters. Dr. Energy Saver went into the affected area and fully removed the existing insulation. We prepared the attic for installation of fresh, clean insulation. We Installed a SuperKneeWall™ Upgrade - Install SilverGlo™ EPS foam board with radiant barrier along roof line, gable end(s) and blocking between floor joists. We then Installed SilverGlo™ on the roof deck.

This homeowner can now enjoy a rodent free home with much better energy efficiency and lower energy bills to boot!

This homeowner in Lee, MA called us because he had a very wet basement in believed he had mold in the walls. When our Home Comfort Specialist arrived, he noted that they had an inadequate sump pump in the home.

We decided the best course of action was to remove that sump pump and install our TripleSafe™ super sump pump. The TripleSafe™ sump pump system has 3 pumps to protect from flooding. The first pump is a 1/3 hp, cast iron Zoeller pump that can pump up to 2,200 gallons per hour, 8 feet high. Should the first pump fail or not be able to keep up with the temporary heavy flow of water, a 1/2 AC back up pump on a separate discharge line can pump 3,900 gallons of water per hour. If the power fails, then a third, battery operated "UltraSump" pump automatically pumps up to 12,000 gallons of water out of your basement! An airtight lid keeps moisture, odors, and radon gas out of your basement.

This homeowner in Lee, MA called us hoping to get information about our mold remediation services. She had a large amount of mold in her attic. Fiberglass insulation is "mold food" and mold spreads easily in an attic if left untreated. On top of that, one of the biggest problems that was causing their mold problem was actually their inefficient insulation. 

Luckily, Fogarty's Home Services had the perfect solution for this customer! We first removed all of the old insulation, preparing the attic for mold removal. After the mold was fully removed and treated, we began re-insulating the attic. We started with air-sealing all cracks and gaps with our ZypFoam™ one-part spray foam. We then installed our TiteShell™ can light covers over all can lights, sealing around them to ensure a tight fit. Then, we insulated the home using our blown-in TruSoft™ cellulose insulation. TruSoft™ insulation is blown into the attic, filling all gaps and odd shaped voids. Now, their home will be much more comfortable - and have less mold! 

This homeowner in Lee, MA reached out to us hoping we would be able to replace his old, moldy attic insulation. Our Home Comfort Specialist came out to the home and recommended some solutions for his issues, including the removal and replacement of the insulation.

In this solution, we first have to remove the old blown-in attic insulation using a long hose attached to a vacuum. Once the attic was cleaned, we started on air sealing the attic with Zypfoam one part spray foam. This seals all cracks and crevices in the attic floor. We then used a different long hose attached to a machine that blows our TruSoft™ cellulose insulation into the attic. TruSoft™ cellulose is able to fill all gaps and odd-shaped voids, as it is blown in insulation.

Now, this homeowner will have a much more comfortable home!